Bringing Wi-Fi 7 to your Company Table

Setting the Network Infrastructure Table

Upgrading your wireless network can be a very worthwhile endeavor. Advances in wireless technology often move faster than other network components and these advances can translate into higher data throughput, more reliable connections, and better security.

Today, upgrading to Wi-Fi 7 (802.11be) is a great choice.  All of the major companies have been releasing certified products since 2024.  It is the current standard for Wi-Fi devices

But as you start planning the rollout of these new Access Points, it is important to look at the supporting infrastructure as well. Replacing your old Access Points with these new models is not as simple as taking the old ones down and plugging in the new.

Just like putting together a Thanksgiving meal, proper planning is the first step!

You are Probably Going to Need More Access Points…

There is the false assumption that as you upgrade your Wireless Network, you will need the same or even less Wireless Access Points.

The opposite is true; those higher modulation rates require a better signal to noise ratio to provide those data rates. This means you need a stronger, cleaner signal between your Access Points and your clients to get those desired throughput numbers.

You also want to have a good ratio of clients per radio. Imagine that each Access Point is a table full of food with only one serving utensil that has to be shared by everyone seated at that table. Too many people at the same table are going to get crowded, especially if they are all hungry for that data!

Another reason for a higher density deployment is if you are starting to use 6.0GHz. That spectrum does not pass through walls as well as 2.4GHz or 5.0GHz. A distance that gave you good 5.0GHz signal is going to be much weaker on 6.0GHz.

Start with an assessment of your current wireless network coverage and then design for the spectrum you are going to be utilizing and the client density of your users.

Do you have the Power for the New Access Points?

These newer Wi-Fi 7 Access Points typically require a lot more power to support them than the old models they are replacing, especially with the additional radio for the 6.0GHz spectrum. An entry level Wi-Fi 7 model might function on PoE+ (802.3at/30W) but most Mid-Tier or Enterprise-Grade Access Points are going to require PoE++ (802.3bt / 60W-90W).

Not being able to provide the additional power to the newer Access Points can result in a less-than half baked result where Access Points will limit which radios will be enabled, remove USB support (if it exists), or in the worst cases will not even turn on the Access Point.

If you are using the Power-Over-Ethernet (PoE) on your switches, not only will you need to verify the PoE ratings on the switchports are compatible, but you will need to verify the switch’s power budget is high enough to support that additional electrical load. This is especially important if you are adding additional Access Points to the switch.

If you are using power-injectors, these are almost always purchased to match the existing Access Points and will most likely need to be replaced to support the new Wi-Fi 7 power requirements. If you are plugging in multiple ports on the Access Points for redundancy, you are going to need at least two power-injectors per Access Point. A survey of the network closets to validate that there are enough electric outlets to accommodate this additional requirement and also any additional APs you plan on deploying.

Using power-injectors are usually not advised. Not only do you lose the ability to remotely power-cycle your APs if needed, but you also lose the ability to remotely monitor the PoE going to the Access Points which is a huge advantage in troubleshooting. Injectors also add an additional point of failure, another required Ethernet jumper cable to worry about, and just do not scale well in a dense environment with the required electrical plugs.

Switchport Speed Bottlenecks

Even if you are not using the PoE on your switches at this time, it is still important to validate the maximum switchport speeds available.

Gone are the days where you could safely assume that any wired connection would be faster than a wireless connection.

Utilizing a switchport on an older switch that only supports 1Gbps or less for a Wi-Fi 7 Access Point can create a data-rate bottleneck that may negate the wireless throughput gains you were expecting by upgrading to Wi-Fi 7.

Some switches have a limited number of higher data rate ports. In order to utilize those switchports, it may be required to move existing connected equipment.

Many of the higher-end Wi-Fi 7 Access Points come with multiple uplinks that can support link aggregation and/or link and power redundancy.

With more and more mission-critical traffic running off of wireless networks, redundancy becomes a necessity. When a wireless outage brings all the autonomous vehicles in the factory or warehouse to a stop, the tolerance for having Access Points go down quickly disappears.

Redundancy and Link Aggregation doubles the number of switchports each AP will occupy. Finding out if there are enough available switchports is a starting point, but if these AP switchports are going to be used for redundancy more work is required to eliminate as many single points of failure as possible.

Depending on the level of redundancy desired, the AP switchport mapping needs to be distributed across different switches (sometimes in different network closets) or switch stack members.

For Link Aggregation, the switchport data rates need to match, and the ports need to be on the same physical or logical switch.

New Ethernet Cabling

One of the last things that immediately comes to mind when working on a Wireless Network are the wires used to get all of those Access Points up and running!

In order to support faster uplink speeds, upgrading your existing wired infrastructure to CAT6 or CAT6A is a minimum requirement when you start upgrading your Access Points to Wi-Fi 7.

When was the last time your looked at your Ethernet cables?

CAT5 cable has a maximum of data speed of 100Mbps and should have been swapped out long ago, and CAT 5E rated cable has a maximum data rate of 1Gbps. Both are not adequate when real-world client speeds on the Wi-Fi 7 can be expected to be at least over 2Gbps.

CAT6 cable can support 10Gbps, but only over shorter distances of 55 meters instead of the full 100 meters that CAT6A supports. If you have Ethernet runs that exceed 55 meters (180ft), make sure that you are using CAT6A.

When you are replacing the Ethernet cabling, you also need to evaluate whether a single cable out to the Access Point is going to be sufficient.

As mentioned in the previous section, many high-end Wi-Fi 7 Access Points come with dual multigigabit Ethernet ports for data link aggregation and/or redundancy. It is best to plan on adding a minimum of two Ethernet cables to every Access Point to capitalize on this feature.

If redundancy is desired, and the Access Points have multiple network closets within 100 meters, distributing these cables from the Access Points to two different closets will provide the best redundancy.

Adding 6.0GHz, the meat and potatoes…

Although introduced in Wi-Fi 6e, opening the 6.0GHz spectrum to your business is a key benefit of upgrading your wireless network to Wi-Fi 7.

But before you begin, did you conduct any wireless surveys designed to supporting the new spectrum?

Because 6.0GHz is a higher frequency, it does not have the same penetration that you would see with 5.0GHz and 2.4GHz. You cannot expect to have the same exact coverage footprint if your network was designed for 5.0GHz or 2.4GHz coverage.

In order to design for the new spectrum, start with a passive survey of your areas to find current coverages, and any interference sources. This survey also verifies that you have accurate and up-to-date maps of your environment.

Having good maps is critical for a predictive survey using 6.0GHz as the base in the new deployment design.

Finally conduct an AP-on-a-Stick to confirm that this software-based design holds up to the real-world environments and that there are no unforeseen issues with any of the new AP placements.

Multi-Link Operation (MLO)

One of the most anticipated features of Wi-Fi 7 is Multi-Link Operation where devices can connect across multiple frequency bands simultaneously. This cycles back to the importance of designing around the 6.0GHz frequency, as this higher frequency has a shorter reach and less penetration through walls.

If the desire is to have clients connecting on all three of the spectrums, the 6.0GHz is going to be the most impacted as a client moves through the areas and will need to be at the heart of any design considerations or you may end up with clients only connecting on two out of the three.

 

320MHz is a large plate to handle on a crowded table…

Wi-Fi 7 has introduced 320MHz wide channel bonding in 6.0GHz for higher speeds, but the number of channels available have remained the same depending on where you are in the world.

In countries that support the full 6.0GHz Band (U-NII-5 to 8), there are 59 20MHz channels to utilize. Each doubling in channel width, reduces the number of channels available by half.

As a result, 40MHz wide channel bonding results in 29 channels, 80MHz results in 14 channels, 160MHz produces 7 channels, and finally when you use 320MHz channels you only have 3 channels left to design around. In countries that only support the Lower 6.0GHz (U-NII-5) the number of 320MHz wide channels is only 1.

Depending on the density of Access Points needed to support your environment, this is not enough channels to avoid creating co-channel interference in most environments and should be avoided especially in any modest sized open-air environment. When designing for 6.0GHz, find the balance of providing the greatest channel bonding that prevents channel overlap.

Eating your Security Vegetables, WPA3

Upgrading your security standards can be more difficult to swallow than a plate of vegetables but moving to the higher security standards of WPA3 is a requirement of utilizing 6.0GHz with authentication.

When moving to WPA3, it is recommended to avoid using “Transition Mode”. Transition mode is meant to allow clients the choice of utilizing WPA2 or WPA3 based on their own capabilities on the same SSID. These old clients cannot use the 6.0GHz spectrum but can continue to use the 5.0GHz and/or 2.4GHz spectrums enabled on that SSID.

The problem stems that lower security standards are now allowed on the same WLAN and to allow that, some security features get compromised such as requiring MFP (management frame protection). It also gives the false impression that WPA3 has been deployed and can easily extend the amount of time this transitory setting will exist on the network.

In organizations that are sensitive to network changes, once deployed this transition mode setting may become permanent to support old legacy clients as opposed to forcing those clients to update with wireless network cards and supplicants that support this new security standard and the 6.0GHz spectrum.

The best course of action is to create a new production WLAN with required WPA3 security standards and transition clients to it. Setup a plan for all clients to move to the new SSID with the scheduled elimination of the older less secure SSID at a clearly defined date that allows the clients to be updated. Keep the old and new SSIDs segmented to help mitigate any impact if the less secure clients are compromised before they are transitioned.

Removing all Leftover Legacy Access Points

When doing a wireless upgrade that will introduce new spectrum, new standards, and/or new security; it is important to swap out the infrastructure completely in the areas where the clients will be actively roaming.

Mixing different models of Access Points, can have unforeseen consequences for clients roaming between Access Points that do not support the same modulation rates, features, and spectrum. This can result in clients dropping off the network as they roam.

If a backend wireless controller is being used, having the older legacy devices still present on the network can limit what code and hardware that the backend controller can use that supports both the new and old Access Points. As features are introduced on newer code releases, you may find yourself stuck on a maintenance release that supports the legacy hardware.

Hopefully you are leaving the table with a better idea of some of the steps needed to be planned out as you upgrade to this newer standard.

But if you are feeling a little overwhelmed, feel free to reach out, we are here to help!

-Erik Klaubert

EIA Lead Wireless Architect

CWNE#139, CCNP Enterprise, Specialist - Enterprise Wireless Design & Implementation, Meraki Master

Next
Next

Why Segmentation Programs Wither on the Vine